Line data Source code
1 : // EnergyPlus, Copyright (c) 1996-2023, The Board of Trustees of the University of Illinois,
2 : // The Regents of the University of California, through Lawrence Berkeley National Laboratory
3 : // (subject to receipt of any required approvals from the U.S. Dept. of Energy), Oak Ridge
4 : // National Laboratory, managed by UT-Battelle, Alliance for Sustainable Energy, LLC, and other
5 : // contributors. All rights reserved.
6 : //
7 : // NOTICE: This Software was developed under funding from the U.S. Department of Energy and the
8 : // U.S. Government consequently retains certain rights. As such, the U.S. Government has been
9 : // granted for itself and others acting on its behalf a paid-up, nonexclusive, irrevocable,
10 : // worldwide license in the Software to reproduce, distribute copies to the public, prepare
11 : // derivative works, and perform publicly and display publicly, and to permit others to do so.
12 : //
13 : // Redistribution and use in source and binary forms, with or without modification, are permitted
14 : // provided that the following conditions are met:
15 : //
16 : // (1) Redistributions of source code must retain the above copyright notice, this list of
17 : // conditions and the following disclaimer.
18 : //
19 : // (2) Redistributions in binary form must reproduce the above copyright notice, this list of
20 : // conditions and the following disclaimer in the documentation and/or other materials
21 : // provided with the distribution.
22 : //
23 : // (3) Neither the name of the University of California, Lawrence Berkeley National Laboratory,
24 : // the University of Illinois, U.S. Dept. of Energy nor the names of its contributors may be
25 : // used to endorse or promote products derived from this software without specific prior
26 : // written permission.
27 : //
28 : // (4) Use of EnergyPlus(TM) Name. If Licensee (i) distributes the software in stand-alone form
29 : // without changes from the version obtained under this License, or (ii) Licensee makes a
30 : // reference solely to the software portion of its product, Licensee must refer to the
31 : // software as "EnergyPlus version X" software, where "X" is the version number Licensee
32 : // obtained under this License and may not use a different name for the software. Except as
33 : // specifically required in this Section (4), Licensee shall not use in a company name, a
34 : // product name, in advertising, publicity, or other promotional activities any name, trade
35 : // name, trademark, logo, or other designation of "EnergyPlus", "E+", "e+" or confusingly
36 : // similar designation, without the U.S. Department of Energy's prior written consent.
37 : //
38 : // THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR
39 : // IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY
40 : // AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
41 : // CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
42 : // CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
43 : // SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
44 : // THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
45 : // OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
46 : // POSSIBILITY OF SUCH DAMAGE.
47 :
48 : #include <EnergyPlus/Autosizing/CoolingWaterDesAirOutletHumRatSizing.hh>
49 : #include <EnergyPlus/Data/EnergyPlusData.hh>
50 : #include <EnergyPlus/DataEnvironment.hh>
51 : #include <EnergyPlus/Psychrometrics.hh>
52 : #include <EnergyPlus/UtilityRoutines.hh>
53 :
54 : namespace EnergyPlus {
55 :
56 443 : Real64 CoolingWaterDesAirOutletHumRatSizer::size(EnergyPlusData &state, Real64 _originalValue, bool &errorsFound)
57 : {
58 443 : if (!this->checkInitialized(state, errorsFound)) {
59 0 : return 0.0;
60 : }
61 443 : this->preSize(state, _originalValue);
62 :
63 443 : if (this->curZoneEqNum > 0) {
64 92 : if (!this->wasAutoSized && !this->sizingDesRunThisZone) {
65 0 : this->autoSizedValue = _originalValue;
66 : } else {
67 92 : if (this->termUnitIU) {
68 4 : Real64 TDpIn = Psychrometrics::PsyTdpFnWPb(state, this->dataDesInletAirHumRat, state.dataEnvrn->StdBaroPress);
69 4 : if (TDpIn <= this->dataDesInletWaterTemp) {
70 0 : this->autoSizedValue = this->dataDesInletAirHumRat;
71 : } else {
72 4 : this->autoSizedValue = min(Psychrometrics::PsyWFnTdbRhPb(state, this->dataDesOutletAirTemp, 0.9, state.dataEnvrn->StdBaroPress),
73 : this->dataDesInletAirHumRat);
74 : }
75 : } else {
76 88 : this->autoSizedValue = this->finalZoneSizing(this->curZoneEqNum).CoolDesHumRat;
77 : }
78 : }
79 351 : } else if (this->curSysNum > 0) {
80 351 : if (!this->wasAutoSized && !this->sizingDesRunThisAirSys) {
81 0 : this->autoSizedValue = _originalValue;
82 : } else {
83 351 : if (this->curOASysNum > 0) { // coil is in OA stream
84 28 : if (this->outsideAirSys(this->curOASysNum).AirLoopDOASNum > -1) {
85 1 : this->autoSizedValue = this->airloopDOAS[this->outsideAirSys(this->curOASysNum).AirLoopDOASNum].PrecoolHumRat;
86 : } else {
87 27 : this->autoSizedValue = this->finalSysSizing(this->curSysNum).PrecoolHumRat;
88 : }
89 323 : } else if (this->dataDesOutletAirHumRat > 0.0) {
90 323 : this->autoSizedValue = this->dataDesOutletAirHumRat;
91 : } else {
92 0 : this->autoSizedValue = this->finalSysSizing(this->curSysNum).CoolSupHumRat;
93 : }
94 : }
95 : }
96 :
97 443 : if (this->wasAutoSized) {
98 940 : if (this->autoSizedValue > this->dataDesInletAirHumRat &&
99 470 : (UtilityRoutines::SameString(this->compType, "COIL:COOLING:WATER") ||
100 438 : UtilityRoutines::SameString(this->compType, "COIL:COOLING:WATER:DETAILEDGEOMETRY"))) {
101 : std::string msg =
102 64 : this->callingRoutine + ":" + " Coil=\"" + this->compName + "\", Cooling Coil has leaving humidity ratio > entering humidity ratio.";
103 32 : this->addErrorMessage(msg);
104 32 : ShowWarningError(state, msg);
105 32 : msg = format(" Wair,in = {:.6R} [kgWater/kgDryAir]", this->dataDesInletAirHumRat);
106 32 : this->addErrorMessage(msg);
107 32 : ShowContinueError(state, msg);
108 32 : msg = format(" Wair,out = {:.6R} [kgWater/kgDryAir]", this->autoSizedValue);
109 32 : this->addErrorMessage(msg);
110 32 : ShowContinueError(state, msg);
111 32 : if (this->dataDesInletAirHumRat > 0.016) {
112 0 : this->autoSizedValue = 0.5 * this->dataDesInletAirHumRat;
113 : } else {
114 32 : this->autoSizedValue = this->dataDesInletAirHumRat;
115 : }
116 32 : msg = "....coil leaving humidity ratio will be reset to:";
117 32 : this->addErrorMessage(msg);
118 32 : ShowContinueError(state, msg);
119 32 : msg = format(" Wair,out = {:.6R} [kgWater/kgDryAir]", this->autoSizedValue);
120 32 : this->addErrorMessage(msg);
121 32 : ShowContinueError(state, msg);
122 : }
123 : // check for dry coil and reset outlet humrat if needed
124 876 : Real64 desSatEnthAtWaterInTemp = Psychrometrics::PsyHFnTdbW(
125 876 : this->dataDesInletWaterTemp, Psychrometrics::PsyWFnTdpPb(state, this->dataDesInletWaterTemp, state.dataEnvrn->StdBaroPress));
126 438 : Real64 desHumRatAtWaterInTemp = Psychrometrics::PsyWFnTdbH(state, this->dataDesInletWaterTemp, desSatEnthAtWaterInTemp, this->callingRoutine);
127 438 : if (this->autoSizedValue < this->dataDesInletAirHumRat && desHumRatAtWaterInTemp > this->dataDesInletAirHumRat) {
128 20 : if (this->autoSizedValue < this->dataDesInletAirHumRat &&
129 10 : (UtilityRoutines::SameString(this->compType, "COIL:COOLING:WATER") ||
130 5 : UtilityRoutines::SameString(this->compType, "COIL:COOLING:WATER:DETAILEDGEOMETRY"))) {
131 10 : std::string msg = this->callingRoutine + ":" + " Coil=\"" + this->compName +
132 : "\", Cooling Coil is running dry for sizing and has minimum humidity ratio at saturation for inlet chilled water "
133 10 : "temperature > design air entering humidity ratio.";
134 5 : this->addErrorMessage(msg);
135 5 : ShowWarningError(state, msg);
136 5 : msg = format(" Wair,in = {:.6R} [kgWater/kgDryAir]", this->dataDesInletAirHumRat);
137 5 : this->addErrorMessage(msg);
138 5 : ShowContinueError(state, msg);
139 5 : msg = format(" Wair,out = {:.6R} [kgWater/kgDryAir]", this->autoSizedValue);
140 5 : this->addErrorMessage(msg);
141 5 : ShowContinueError(state, msg);
142 5 : msg = format(" Inlet chilled water temperature = {:.3R} [C]", this->dataDesInletWaterTemp);
143 5 : this->addErrorMessage(msg);
144 5 : ShowContinueError(state, msg);
145 5 : msg = format(" Minimum humidity ratio at saturation for inlet chilled water temperature = {:.6R} [kgWater/kgDryAir]",
146 5 : desHumRatAtWaterInTemp);
147 5 : this->addErrorMessage(msg);
148 5 : ShowContinueError(state, msg);
149 5 : this->autoSizedValue = this->dataDesInletAirHumRat;
150 5 : msg = "....coil leaving humidity ratio will be reset to:";
151 5 : this->addErrorMessage(msg);
152 5 : ShowContinueError(state, msg);
153 5 : msg = format(" Wair,out = {:.6R} [kgWater/kgDryAir]", this->autoSizedValue);
154 5 : this->addErrorMessage(msg);
155 5 : ShowContinueError(state, msg);
156 : }
157 : }
158 : }
159 443 : if (this->overrideSizeString) {
160 443 : if (this->isEpJSON) this->sizingString = "design_outlet_air_humidity_ratio [kgWater/kgDryAir]";
161 : }
162 443 : this->selectSizerOutput(state, errorsFound);
163 443 : if (this->isCoilReportObject)
164 443 : state.dataRptCoilSelection->coilSelectionReportObj->setCoilLvgAirHumRat(state, this->compName, this->compType, this->autoSizedValue);
165 443 : return this->autoSizedValue;
166 : }
167 :
168 2313 : } // namespace EnergyPlus
|