Line data Source code
1 : // EnergyPlus, Copyright (c) 1996-2023, The Board of Trustees of the University of Illinois,
2 : // The Regents of the University of California, through Lawrence Berkeley National Laboratory
3 : // (subject to receipt of any required approvals from the U.S. Dept. of Energy), Oak Ridge
4 : // National Laboratory, managed by UT-Battelle, Alliance for Sustainable Energy, LLC, and other
5 : // contributors. All rights reserved.
6 : //
7 : // NOTICE: This Software was developed under funding from the U.S. Department of Energy and the
8 : // U.S. Government consequently retains certain rights. As such, the U.S. Government has been
9 : // granted for itself and others acting on its behalf a paid-up, nonexclusive, irrevocable,
10 : // worldwide license in the Software to reproduce, distribute copies to the public, prepare
11 : // derivative works, and perform publicly and display publicly, and to permit others to do so.
12 : //
13 : // Redistribution and use in source and binary forms, with or without modification, are permitted
14 : // provided that the following conditions are met:
15 : //
16 : // (1) Redistributions of source code must retain the above copyright notice, this list of
17 : // conditions and the following disclaimer.
18 : //
19 : // (2) Redistributions in binary form must reproduce the above copyright notice, this list of
20 : // conditions and the following disclaimer in the documentation and/or other materials
21 : // provided with the distribution.
22 : //
23 : // (3) Neither the name of the University of California, Lawrence Berkeley National Laboratory,
24 : // the University of Illinois, U.S. Dept. of Energy nor the names of its contributors may be
25 : // used to endorse or promote products derived from this software without specific prior
26 : // written permission.
27 : //
28 : // (4) Use of EnergyPlus(TM) Name. If Licensee (i) distributes the software in stand-alone form
29 : // without changes from the version obtained under this License, or (ii) Licensee makes a
30 : // reference solely to the software portion of its product, Licensee must refer to the
31 : // software as "EnergyPlus version X" software, where "X" is the version number Licensee
32 : // obtained under this License and may not use a different name for the software. Except as
33 : // specifically required in this Section (4), Licensee shall not use in a company name, a
34 : // product name, in advertising, publicity, or other promotional activities any name, trade
35 : // name, trademark, logo, or other designation of "EnergyPlus", "E+", "e+" or confusingly
36 : // similar designation, without the U.S. Department of Energy's prior written consent.
37 : //
38 : // THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR
39 : // IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY
40 : // AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
41 : // CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
42 : // CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
43 : // SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
44 : // THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
45 : // OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
46 : // POSSIBILITY OF SUCH DAMAGE.
47 :
48 : #ifndef ChillerIndirectAbsorption_hh_INCLUDED
49 : #define ChillerIndirectAbsorption_hh_INCLUDED
50 :
51 : // ObjexxFCL Headers
52 : #include <ObjexxFCL/Array1D.hh>
53 :
54 : // EnergyPlus Headers
55 : #include <EnergyPlus/Data/BaseData.hh>
56 : #include <EnergyPlus/DataGlobals.hh>
57 : #include <EnergyPlus/EnergyPlus.hh>
58 : #include <EnergyPlus/Plant/DataPlant.hh>
59 : #include <EnergyPlus/PlantComponent.hh>
60 :
61 : namespace EnergyPlus {
62 :
63 : // Forward declarations
64 : struct EnergyPlusData;
65 :
66 : namespace ChillerIndirectAbsorption {
67 :
68 1 : struct ReportVars
69 : {
70 : // Members
71 : Real64 PumpingPower = 0.0; // reporting: W - electric pumping power
72 : Real64 QGenerator = 0.0; // reporting: W - steam heat transfer rate
73 : Real64 QEvap = 0.0; // reporting: W - evaporator heat transfer rate
74 : Real64 QCond = 0.0; // reporting: W - condenser heat transfer rate
75 : Real64 PumpingEnergy = 0.0; // reporting: J - electric pumping power
76 : Real64 GeneratorEnergy = 0.0; // reporting: J - steam heat transfer rate
77 : Real64 EvapEnergy = 0.0; // reporting: J - evaporator heat transfer rate
78 : Real64 CondEnergy = 0.0; // reporting: J - condenser heat transfer rate
79 : Real64 CondInletTemp = 0.0; // reporting: C - condenser inlet temperature
80 : Real64 EvapInletTemp = 0.0; // reporting: C - evaporator inlet temperature
81 : Real64 CondOutletTemp = 0.0; // reporting: C - condenser outlet temperature
82 : Real64 EvapOutletTemp = 0.0; // reporting: C - evaporator outlet temperature
83 : Real64 Evapmdot = 0.0; // reporting: kg/ - evaporator mass flow rate
84 : Real64 Condmdot = 0.0; // reporting: kg/ - condenser mass flow rate
85 : Real64 Genmdot = 0.0; // reporting: generators mass flow rate when connected to plant
86 : Real64 SteamMdot = 0.0; // reporting: kg/s - steam mass flow rate
87 : Real64 ActualCOP = 0.0; // reporting: coefficient of performance = QEvap/QGenerator
88 : Real64 ChillerPartLoadRatio = 0.0; // reporting: part-load ratio
89 : Real64 ChillerCyclingFrac = 0.0; // reporting: chiller on/off cycling fraction
90 : Real64 LoopLoss = 0.0; // reporting: W - loop loss from absorber outlet to condensate pump inlet
91 : };
92 :
93 6 : struct IndirectAbsorberSpecs : PlantComponent
94 : {
95 : // Members
96 : std::string Name; // user identifier
97 : Real64 NomCap = 0.0; // W - design nominal capacity of Absorber
98 : bool NomCapWasAutoSized = false; // true if Nominal capacity was autosize on input
99 : Real64 NomPumpPower = 0.0; // W - design nominal capacity of Absorber
100 : bool NomPumpPowerWasAutoSized = false; // true if nominal pump power was autosize on input
101 : Real64 EvapVolFlowRate = 0.0; // m3/s - design nominal water volumetric flow rate through the evaporator
102 : bool EvapVolFlowRateWasAutoSized = false; // true if evaporator flow rate was autosize on input
103 : Real64 CondVolFlowRate = 0.0; // m3/s - design nominal water volumetric flow rate through the condenser
104 : bool CondVolFlowRateWasAutoSized = false; // true if condenser flow rate was autosize on input
105 : Real64 EvapMassFlowRateMax = 0.0; // kg/s - Max Design Evaporator Mass Flow Rate converted from Volume Flow Rate
106 : Real64 CondMassFlowRateMax = 0.0; // Max Design Condenser Mass Flow Rate [kg/s]
107 : Real64 GenMassFlowRateMax = 0.0; // kg/s - Max Design Generator Mass Flow Rate converted from Volume Flow Rate
108 : Real64 MinPartLoadRat = 0.0; // (BLAST MIN) min allowed operating frac full load
109 : Real64 MaxPartLoadRat = 0.0; // (BLAST MAX) max allowed operating frac full load
110 : Real64 OptPartLoadRat = 0.0; // (BLAST BEST) optimal operating frac full load
111 : Real64 TempDesCondIn = 0.0; // C - (BLAST ADJTC(1)The design secondary loop fluid
112 : // temperature at the Absorber condenser side inlet
113 : Real64 MinCondInletTemp = 0.0; // C - minimum condenser inlet temperature for chiller operation
114 : Real64 MinGeneratorInletTemp = 0.0; // C - minimum generator inlet temperature for chiller operation
115 : Real64 TempLowLimitEvapOut = 0.0; // C - low temperature shut off
116 : Real64 GeneratorVolFlowRate = 0.0; // m3/s - hot water volumetric flow rate through generator
117 : bool GeneratorVolFlowRateWasAutoSized = false; // true if hot water flow was autosize on input
118 : Real64 GeneratorSubcool = 0.0; // C - amount of subcooling in steam generator
119 : Real64 LoopSubcool = 0.0; // C - amount of subcooling in steam generator
120 : Real64 GeneratorDeltaTemp = -99999.0; // C - generator fluid temperature difference (water only)
121 : bool GeneratorDeltaTempWasAutoSized = true; // true if generator delta T was autosize on input
122 : Real64 SizFac = 0.0; // Sizing factor
123 : int EvapInletNodeNum = 0; // Node number on the inlet side of the plant
124 : int EvapOutletNodeNum = 0; // Node number on the outlet side of the plant
125 : int CondInletNodeNum = 0; // Node number on the inlet side of the condenser
126 : int CondOutletNodeNum = 0; // Node number on the outlet side of the condenser
127 : int GeneratorInletNodeNum = 0; // Generator inlet node number, steam/water side
128 : int GeneratorOutletNodeNum = 0; // Generator outlet node number, steam/water side
129 : int GeneratorInputCurvePtr = 0; // Index to steam use curve as a function of PLR
130 : int PumpPowerCurvePtr = 0; // Index to pump power curve as a function of PLR
131 : int CapFCondenserTempPtr = 0; // Index to capacity as a function of absorber temp curve
132 : int CapFEvaporatorTempPtr = 0; // Index to capacity as a function of evaporator temp curve
133 : int CapFGeneratorTempPtr = 0; // Index to capacity as a function of generator temp curve
134 : int HeatInputFCondTempPtr = 0; // Index to generator heat input as a function of absorber temp
135 : int HeatInputFEvapTempPtr = 0; // Index to generator heat input as a function of absorber temp
136 : int ErrCount2 = 0; // error counter
137 : DataLoopNode::NodeFluidType GenHeatSourceType =
138 : DataLoopNode::NodeFluidType::Blank; // Generator heat source type, DataLoopNode::NodeFluidType::Steam=3 or
139 : // DataLoopNode::NodeFluidType::Water=2
140 : int SteamFluidIndex = 0; // index to generator fluid type
141 : bool Available = false; // need an array of logicals--load identifiers of available equipment
142 : bool ON = false; // simulate the machine at it's operating part load ratio
143 : DataPlant::FlowMode FlowMode = DataPlant::FlowMode::Invalid; // one of 3 modes for component flow during operation
144 : bool ModulatedFlowSetToLoop = false; // True if the setpoint is missing at the outlet node
145 : bool ModulatedFlowErrDone = false; // true if setpoint warning issued
146 : int MinCondInletTempCtr = 0; // Low condenser temp warning message counter
147 : int MinCondInletTempIndex = 0; // Low condenser temp warning message index
148 : int MinGenInletTempCtr = 0; // Low generator temp warning message counter
149 : int MinGenInletTempIndex = 0; // Low generator temp warning message index
150 : PlantLocation CWPlantLoc; // chilled water plant loop component index
151 : PlantLocation CDPlantLoc; // condenser water plant loop component index
152 : PlantLocation GenPlantLoc; // generator plant loop component index
153 : bool FaultyChillerSWTFlag = false; // True if the chiller has SWT sensor fault
154 : int FaultyChillerSWTIndex = 0; // Index of the fault object corresponding to the chiller
155 : Real64 FaultyChillerSWTOffset = 0.0; // Chiller SWT sensor offset
156 : bool PossibleSubcooling = false; // flag to indicate chiller is doing less cooling that requested
157 : Real64 CondMassFlowRate = 0.0; // Kg/s - condenser mass flow rate, water side
158 : Real64 EvapMassFlowRate = 0.0; // Kg/s - evaporator mass flow rate, water side
159 : Real64 GenMassFlowRate = 0.0; // Kg/s - steam mass flow rate, water side
160 : Real64 CondOutletTemp = 0.0; // C - condenser outlet temperature, water side
161 : Real64 EvapOutletTemp = 0.0; // C - evaporator outlet temperature, water side
162 : Real64 GenOutletTemp = 0.0; // C - generator fluid outlet temperature
163 : Real64 SteamOutletEnthalpy = 0.0; // J/kg - generator fluid outlet enthalpy
164 : Real64 PumpingPower = 0.0; // W - rate of Absorber energy use
165 : Real64 PumpingEnergy = 0.0; // J - Absorber energy use
166 : Real64 QGenerator = 0.0; // W - rate of Absorber steam use
167 : Real64 GeneratorEnergy = 0.0; // J - Absorber steam use
168 : Real64 QEvaporator = 0.0; // W - rate of heat transfer to the evaporator coil
169 : Real64 EvaporatorEnergy = 0.0; // J - heat transfer to the evaporator coil
170 : Real64 QCondenser = 0.0; // W - rate of heat transfer to the condenser coil
171 : Real64 CondenserEnergy = 0.0; // J - heat transfer to the condenser coil
172 : Real64 ChillerONOFFCyclingFrac = 0.0; // fraction of time chiller is on
173 : Real64 EnergyLossToEnvironment = 0.0; // J - piping energy loss from generator outlet to pump inlet
174 : bool GenInputOutputNodesUsed = false;
175 : bool MyOneTimeFlag = true;
176 : bool MyEnvrnFlag = true;
177 : ReportVars Report;
178 : DataBranchAirLoopPlant::ControlType EquipFlowCtrl = DataBranchAirLoopPlant::ControlType::Invalid;
179 :
180 : static PlantComponent *factory(EnergyPlusData &state, std::string const &objectName);
181 :
182 : void simulate([[maybe_unused]] EnergyPlusData &state,
183 : const PlantLocation &calledFromLocation,
184 : bool FirstHVACIteration,
185 : Real64 &CurLoad,
186 : bool RunFlag) override;
187 :
188 : void getDesignCapacities(
189 : EnergyPlusData &state, const PlantLocation &calledFromLocation, Real64 &MaxLoad, Real64 &MinLoad, Real64 &OptLoad) override;
190 :
191 : void getSizingFactor(Real64 &sizFac) override;
192 :
193 : void onInitLoopEquip([[maybe_unused]] EnergyPlusData &state, const PlantLocation &calledFromLocation) override;
194 :
195 : void oneTimeInit(EnergyPlusData &state) override;
196 :
197 : void initialize(EnergyPlusData &state, bool RunFlag, Real64 MyLoad);
198 :
199 : void setupOutputVars(EnergyPlusData &state);
200 :
201 : void sizeChiller(EnergyPlusData &state);
202 :
203 : void updateRecords(EnergyPlusData &state, Real64 MyLoad, bool RunFlag);
204 :
205 : void calculate(EnergyPlusData &state, Real64 MyLoad, bool RunFlag);
206 : };
207 :
208 : void GetIndirectAbsorberInput(EnergyPlusData &state);
209 :
210 : } // namespace ChillerIndirectAbsorption
211 :
212 1542 : struct ChillerIndirectAbsoprtionData : BaseGlobalStruct
213 : {
214 : bool GetInput = true;
215 : Array1D<ChillerIndirectAbsorption::IndirectAbsorberSpecs> IndirectAbsorber;
216 :
217 0 : void clear_state() override
218 : {
219 0 : *this = ChillerIndirectAbsoprtionData();
220 0 : }
221 : };
222 :
223 : } // namespace EnergyPlus
224 :
225 : #endif
|